两大学CAT 6509配置
1、主要配置内容
主要包括交换引擎及路由模块配置两大部分。
1.1交换引擎配置内容包括：
1. 配置系统管理密码
2. 配置管理接口SC0
3. 配置与主干交换机CAT3524相连1000M端口为TRUNK模式
4.配置VLAN,包括创建VLAN DOMAIN域名,设置CAT6509为VTP SERVER模式,及创建VLAN。
1.2 CAT6509上路由模块配置内容包括：
1. 配置系统管理密码
2. 配置不同VLAN的INTERFACE(接口)IP地址
3.配置动态路由协议OSPF

2、配置内容说明
以下就针对具体配置清单加以说明：

CAT6509> (enable) show config //SHOW CONFIG 命令用以查看当前配置
This command shows non-default configurations only.
Use 'show config all' to show both default and non-default configurations.
begin
!
# ***** NON-DEFAULT CONFIGURATION *****
!
!
#time: Fri Nov 3 2000, 12:21:24
!
#version 5.4(2)
!
!
#system web interface version Engine: 5.1 ADP device: Cat6000 ADP Version: 1.2 A
DK: 31
!
set password $2$MDww$YAGIzktKTFVBaOlneWe7Z/ //SET PASSWORD (密码)设置普通登录密码
set enablepass $2$NUcp$0f41FgSFEqqFxDsIKC4/A. //SET ENABLEPASS (密码)设置超级用户密码
!
#system
set system name CAT6509
!
#!
#vtp
set vtp domain ZZDX //设置VLAN 的DOMAIN 名为ZZDX
//以下为创建VLAN,共创建17个VLAN.
主要命令格式为SET VLAN +(VLAN 序号) NAME+(VLAN 名)
set vlan 1 name default type ethernet mtu 1500 said 100001 state active
set vlan 2 name SYL-CENTER type ethernet mtu 1500 said 100002 state active
set vlan 3 name BGL type ethernet mtu 1500 said 100003 state active
set vlan 4 name JXL type ethernet mtu 1500 said 100004 state active
set vlan 5 name SYL5-DIANZI type ethernet mtu 1500 said 100005 state active
set vlan 6 name SYL5-KEJIAN type ethernet mtu 1500 said 100006 state active
set vlan 7 name SYL4-XI-MASTER type ethernet mtu 1500 said 100007 state active
set vlan 8 name SYL4-XI-NT type ethernet mtu 1500 said 100008 state active
set vlan 9 name SYL4-XI-NOVELL type ethernet mtu 1500 said 100009 state active
set vlan 11 name LABE402 type ethernet mtu 1500 said 100011 state active
set vlan 12 name LABE404 type ethernet mtu 1500 said 100012 state active
set vlan 13 name TUSHUGUAN type ethernet mtu 1500 said 100013 state active
set vlan 14 name LABE403 type ethernet mtu 1500 said 100014 state active
set vlan 15 name SYL5-XI type ethernet mtu 1500 said 100015 state active
set vlan 16 name TUSHUGUAN1 type ethernet mtu 1500 said 100016 state active
set vlan 17 name LABE406 type ethernet mtu 1500 said 100017 state active
//以下VLAN为系统保留默认设置,非配置部分
set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active
set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state activ
e stp ieee
set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active st
p ibm
set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state acti
ve mode srb aremaxhop 7 stemaxhop 7 backupcrf off
!
#ip //以下命令主要是为方便管理用
set interface sc0 1 10.10.1.1/255.255.255.0 10.10.1.255 //配置管理接口SC0 IP地址为10.10.1.1,命令格式如上

set ip route 0.0.0.0/0.0.0.0 10.10.1.254 //设置10.10.1.254为其网关地址
!
#command alias
set alias bg telnet 10.10.1.7 //设置命令行的别名,即要TELNET 10.10.1.7,只须敲BG即可,主要为方便管理员操作,BG指办公楼CAT3524,依此类推.
set alias jx telnet 10.10.1.8
set alias xsy telnet 10.10.1.9
set alias dsy telnet 10.10.1.2
set alias 2621 telnet 10.10.1.253
set alias 6509 router session 15
!
#set boot command //以下配置不要随便改动
set boot config-register 0x102
set boot system flash bootflash:cat6000-supcv.5-4-2.bin
#port channel //此处为GIGABIT CHANNEL 设置,没有用到
set port channel 1/2 1
set port channel 2/1-4 2
set port channel 2/5,2/7-8 3
set port channel 1/1 38
set port channel 2/6 39
!
# default port status is enable
!
!
#module 1 : 2-port 1000BaseX Supervisor
set vlan 2 1/1 // 设置端口1/1到VLAN 2,1/1连到SUN主服务器
set port flowcontrol 1/1 receive desired // 设置端口1/1流控
set trunk 1/1 off isl 1-1005 //关闭端口1/1的TRUNK模式
set trunk 1/1 off isl 1-1005 //关闭端口1/1的TRUNK模式
set trunk 1/2 auto isl 1-1005 //设置端口1/2为TRUNK自适应模式
set port channel 1/1 mode off //关闭端口1/1的CHANNEL 模式
!
#module 2 : 8-port 1000BaseX Ethernet
set vlan 2 2/6
set trunk 2/1 on isl 1-1005 //以下将连往各大楼CAT3524的端口设为TRUNK模式,主干1000M口必须设为TRUNK模式,以支持VLAN配置
set trunk 2/2 on isl 1-1005
set trunk 2/3 on isl 1-1005
set trunk 2/4 on isl 1-1005
set trunk 2/5 on isl 1-1005
set trunk 2/6 auto isl 1-1005
set trunk 2/7 auto isl 1-1005
set trunk 2/8 auto isl 1-1005
!
#module 3 empty
!
#module 4 empty
!
#module 5 empty
!
#module 6 empty
!
#module 7 empty
!
#module 8 empty
!
#module 9 empty
!
#module 15 : 1-port Multilayertch Feature Card //CAT6509上路由模块号为15
!
#module 16 empty
end
进入CAT6509上路由模块进行配置用SESSION 15命令
以下就针对具体配置清单加以说明:
CAT6509路由模块配置清单:(//后为注释文字)
router_6509#show run //此命令用来查看当前运行的配置
Building configuration...

Current configuration:
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname router_6509 //为路由模块命名,即命令行前的提示符
!
boot system flash bootflash:c6msfc-is-mz.121-1.E //指定系统引导文件位置,不要随便更改
enable password 123 //设置超级用户密码,命令格式为ENABLE PASSWORD+密码
!
ip subnet-zero
ip cef
no ip domain-lookup
!
mls rp ip
mls rp ipx
!
!
//配置VLAN1接口的IP地址,即VLAN1的网关地址,配置过程,ENABLE进入超级用户模式,CONFIG T进入配置模式,出现CAT6509_ROUTER/CONFIG>提示符,INTERFACE VLAN 1 进入接口配置模式,CAT6509_ROUTER/CONFIG/CONFIG_IF>提示符,即可开始配置.
interface Vlan1
ip address 10.10.1.254 255.255.255.0 //配置VLAN1接口地址
!
interface Vlan2
ip address 10.10.2.254 255.255.255.0 //配置VLAN2接口地址
!
interface Vlan3
ip address 10.10.3.254 255.255.255.0 //配置VLAN3接口地址
!
interface Vlan4
ip address 10.10.4.254 255.255.255.0 //配置VLAN4接口地址
!
interface Vlan5
ip address 10.10.5.254 255.255.255.0 //配置VLAN5接口地址
!
interface Vlan6
ip address 10.10.6.254 255.255.255.0 //配置VLAN6接口地址
!
interface Vlan7
ip address 10.10.7.254 255.255.255.0 //配置VLAN7接口地址
!
interface Vlan8
ip address 10.10.8.254 255.255.255.0 //配置VLAN8接口地址
!
interface Vlan9
ip address 10.10.9.254 255.255.255.0 //配置VLAN9接口地址
!
interface Vlan10
no ip address //配置VLAN10接口地址
!
interface Vlan11
ip address 10.10.11.254 255.255.255.0 //配置VLAN11接口地址
!
interface Vlan12
ip address 10.10.12.254 255.255.255.0 //配置VLAN12接口地址
!
interface Vlan13
ip address 10.10.14.254 255.255.255.0 //配置VLAN13接口地址
!
interface Vlan14
ip address 10.10.13.254 255.255.255.0 //配置VLAN14接口地址
!
interface Vlan15
ip address 10.10.15.254 255.255.255.0 //配置VLAN15接口地址
!
interface Vlan16
ip address 10.10.16.254 255.255.255.0 //配置VLAN16接口地址
!
interface Vlan17
ip address 10.10.17.254 255.255.255.0 //配置VLAN17接口地址
!
router ospf 1 //以下为动态路由协议OSPF的有关配置
//以下将所有VLAN子网连接向其余路由器宣告
network 10.10.1.0 0.0.0.255 area 0 //宣告子网10.10.1.0
network 10.10.2.0 0.0.0.255 area 0 //宣告子网10.10.2.0
network 10.10.3.0 0.0.0.255 area 0 //宣告子网10.10.3.0
network 10.10.4.0 0.0.0.255 area 0 //宣告子网10.10.4.0
network 10.10.5.0 0.0.0.255 area 0 //宣告子网10.10.5.0
network 10.10.6.0 0.0.0.255 area 0 //宣告子网10.10.6.0
network 10.10.7.0 0.0.0.255 area 0 //宣告子网10.10.7.0
network 10.10.8.0 0.0.0.255 area 0 //宣告子网10.10.8.0
network 10.10.9.0 0.0.0.255 area 0 //宣告子网10.10.9.0
network 10.10.11.0 0.0.0.255 area 0 //宣告子网10.10.11.0
network 10.10.12.0 0.0.0.255 area 0 //宣告子网10.10.12.0
network 10.10.13.0 0.0.0.255 area 0 //宣告子网10.10.13.0
network 10.10.14.0 0.0.0.255 area 0 //宣告子网10.10.14.0
network 10.10.15.0 0.0.0.255 area 0 //宣告子网10.10.15.0
network 10.10.16.0 0.0.0.255 area 0 //宣告子网10.10.16.0
network 10.10.17.0 0.0.0.255 area 0 //宣告子网10.10.17.0
!
ip classless
ip route 0.0.0.0 0.0.0.0 10.10.1.253 //设置缺省路由指向CISCO2621路由器
no ip http server
!//以下主要为提供网管有关的SNMP参数设置
snmp-server engineID local 000000090200000021000000
snmp-server community public RW //设置可读写网管通讯串为PUBLIC
snmp-server community private RO //设置只读网管通讯串为PRIVATE
snmp-server enable traps snmp
snmp-server enable traps hsrp
snmp-server enable traps config
snmp-server enable traps entity
snmp-server enable traps bgp
snmp-server enable traps rsvp
snmp-server enable traps frame-relay
snmp-server enable traps rtr
snmp-server enable traps dlsw
!
line con 0
transport input none
//对虚拟终端0-4进行设置,即设置远程TELNET 的登录密码及用户权限,步骤为CONFIG T进入配置模式,LINE VTY 0 4进入LINE接口配置模式,privilege level 设置权限,PASSWORD 设置登录密码
line vty 0 4
privilege level 15
password 123
login
!
end

备注：

• 上一篇: 蓝盟IT外包，元宇宙：四梁八柱是什么
  下一篇: Catalyst数据包监控类型SPAN/RSPAN与配置

• 分享到：