Enter password:

WS4006_1> (enable) sh mod

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseX Supervisor WS-X4013 no ok

3 3 6 1000BaseX Ethernet WS-X4306 no ok

4 4 34 Router Switch Card WS-X4232-L3 no ok


Mod Module-Name Serial-Num

--- -------------------- --------------------

1 JAE060906GZ

3 JAE04470A10

4 JAB052105F2


Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

1 00-08-e3-86-06-00 to 00-08-e3-86-09-ff 3.2 5.4(1) 6.3(1)

3 00-04-27-55-93-2c to 00-04-27-55-93-31 2.0

4 00-04-9a-50-16-4c to 00-04-9a-50-16-6d 1.7 12.0(7)W5( 12.0(10)W5(18f)



WS4006_1> (enable) sh config

This command shows non-default configurations only.

Use 'show config all' to show both default and non-default configurations.

.............

..................


..................

....................



..


begin

!

# ***** NON-DEFAULT CONFIGURATION *****

!

!

#time: Tue Mar 18 2003, 23:11:06

!

#version 6.3(1)

!

!

#system web interface version(s)

set password $2$ZtNY$yuqPHi7CpjwCs0blr9mxG0

set enablepass $2$rY7u$b9D5DEa661dt46OwWq5ts/

!

#test

set test diaglevel minimal

!

#system

set system name ZX_WS4006_1

set system contact Center-sw

!

#frame distribution method

set port channel all distribution mac both

!

#vtp

set vtp domain cs1yhis

set vlan 1 name default type ethernet mtu 1500 said 100001 state active

set vlan 2 name JiGuan type ethernet mtu 1500 said 100002 state active

set vlan 3 name YeWu type ethernet mtu 1500 said 100003 state active

set vlan 4 name XXZX type ethernet mtu 1500 said 100004 state active

set vlan 100 name yibao type ethernet mtu 1500 said 100100 state active

set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active

set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state activ

e stp ieee

set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active st

p ibm

set vlan 5-20

set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state acti

ve mode srb aremaxhop 0 stemaxhop 0 backupcrf off

!

#ip

set interface sc0 1 192.168.1.250/255.255.255.0 192.168.1.255


set interface sl0 192.168.168.1 255.255.255.0

set interface sl0 down

set interface me1 192.0.2.1 255.255.255.0 192.0.2.255


set ip route 0.0.0.0/0.0.0.0 192.168.1.254

!

#dns

set ip dns server 202.103.96.68 primary

set ip dns server 202.103.4.238

!

#syslog

set logging level cops 2 default

!

#set boot command

set boot config-register 0x2

set boot system flash bootflash:cat4000.6-3-1.bin

set boot system flash bootflash:cat4000.5-5-8.bin

!

#mls

set mls nde disable

!

#port channel

set port channel 4/1-2 25

!

#http configuration

set ip http server enable

!

#module 1 : 2-port 1000BaseX Supervisor

set udld enable 1/1-2

!

#module 2 empty

!

#module 3 : 6-port 1000BaseX Ethernet

set udld enable 3/6

set trunk 3/3 on dot1q 1-1005

set trunk 3/4 on dot1q 1-1005

set trunk 3/5 on dot1q 1-1005

set trunk 3/6 on dot1q 1-1005

!

#module 4 : 34-port Router Switch Card

set trunk 4/1 nonegotiate dot1q 1-1005

set trunk 4/2 nonegotiate dot1q 1-1005

set port channel 4/1-2 mode on

!

#module 5 empty

!

#module 6 empty

end

WS4006_1> (enable)



WS4006_1> (enable) sess 3

Feature not supported on Module 3.

WS4006_1> (enable) sess 4

Trying IntlgLineCard-4...

Connected to IntlgLineCard-4.

Escape character is '^]'.



User Access Verification


Password:

VLAN>en

Password:

VLAN-gw#sh run

Building configuration...


Current configuration:

!

version 12.0

no service pad

service timestamps debug uptime

service timestamps log uptime

service password-encryption

!

hostname VLAN

!

enable secret 5 $1$j6xO$q2wF0qaki76qo6hr3bYlt.

enable password 7 070E25414707

!

ip subnet-zero

no ip domain-lookup

ip name-server 202.103.96.68

ip name-server 202.103.100.100

!

!

!

interface Port-channel1

description This is interface is configured for routing with native vlan 1 to 4

no ip address

no ip redirects

no ip directed-broadcast

hold-queue 300 in

!

interface Port-channel1.1

encapsulation dot1Q 1 native

ip address 192.1.1.254 255.255.255.0 secondary

ip address 192.168.1.254 255.255.255.0

no ip redirects

no ip directed-broadcast

!

interface Port-channel1.2

description This interface is connected to vlan 2 which is connected to vlan

encapsulation dot1Q 2

ip address 192.168.2.254 255.255.255.0

no ip redirects

no ip directed-broadcast

!

interface Port-channel1.3

description This interface is connected to vlan 3 which is connected to vlan 3

encapsulation dot1Q 3

ip address 192.168.3.254 255.255.255.0

no ip redirects

no ip directed-broadcast

!

interface FastEthernet1

description This is the out of band interface that you can use for management

ip address 172.168.1.1 255.255.255.0

no ip directed-broadcast

!

interface GigabitEthernet1

no ip address

no ip directed-broadcast

!

interface GigabitEthernet2

no ip address

no ip directed-broadcast

!

interface GigabitEthernet3

description This interface is both port gig3 and gig4 are part of the channel 1

no ip address

no ip directed-broadcast

no negotiation auto

channel-group 1

!

interface GigabitEthernet4

description This interface is both port gig3 and gig4 are part of the channel 1

no ip address

no ip directed-broadcast

no negotiation auto

channel-group 1

!

ip classless

!

!

line con 0

transport input none

line aux 0

line vty 0 4

password 7 104D000A0618

login

!

end


VLAN#

备注：

• 上一篇: 蓝盟IT外包，元宇宙：四梁八柱是什么
  下一篇: 在Catalyst交换机配置TACACS+、RADIUS和 Kerberos

• 分享到：