Password Recovery Procedure

for the Cisco Cache Engine 500

Description

This document describes the administration password recovery procedure for the Cisco Cache Engine 500.

Note: Your configuration is lost after perfoming this password recovery. It is not possible to keep your configuration when recovering a lost administrative password.

Step-by-Step Procedure

Establish a console connection to the Cache Engine and reload the device or type reload or reboot at the command line. While the Cache Engine is rebooting, press any key to interrupt the low level configuration countdown.
At the prompt, type p to display the configuration menu.
At the prompt, type c to enter the configuration mode. Use:

a period (.) to clear a field
a dash (-) to go to the previous field
the Enter key to go to the next field
^D to quit

Press Enter nine times until the field flags are displayed.
Enter the value 0x4000 at the prompt and press Enter. This flag will allow the cache engine to bypass the nonvolatile RAM (NVRAM) configuration.
Type @ to reboot the Cache Engine. At this point, the Cache Engine is not password-protected.
To configure a new password, type configure terminal to enter the configuration mode.
Type user modify username admin password cisco to make "cisco" the new password.
Type write or copy running startup to commit the changes.
Reload the Cache Engine.
To set the flags back to their original value of 0x0, repeat steps 3 and 4 and enter 0x0 in the field flags.

Example of Password Recovery on a Cisco Cache Engine 500

The following example shows password recovery on a Cisco Cache Engine 500:

ce500#reload System configuration has been modified. Save?[yes]: y Building configuration.... . [OK] 
Proceed with reload?[confirm] 

Proceed with clean WCCP shutdown?[confirm] 

Existing connections =     0 Press ^C to skip clean WCCP shutdown and reload 
Waiting (113 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (107 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (100 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (93 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (87 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (80 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (73 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (67 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (60 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (53 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (47 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (40 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (33 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (27 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 
Waiting (21 seconds) for WCCP shutdown. Press ^C to skip shutdown and reload 

303949 bytes 
copying bootagent 
boot start: 0x7fee000 
starting new system - entry 0x8010 
0x43d2200 (tCallback2): 
NCR810_ 
  
Press any key to stop auto-boot... 
g5 
[CE500 Series]: p  boot device (flash,net) [               flash]: 
                   flags [                   0]: 

[CE500 Series]: c '.' = clear field;  '-' = go to previous field;  ^D = quit 

 boot device (flash,net) [               flash]: 
               file name [                    ]: 
        cache IP address [                    ]: 
         IP network mask [                    ]: 
       server IP address [                    ]: 
      gateway IP address [                    ]: 
 protocol (rcp,ftp,tftp) [                    ]: 
                username [                    ]: 
                password [                    ]: 
                   flags [                   0]: 0x4000 


. . [CE500 Series]: @ boot device (flash,net) [               flash]: 
                   flags [              0x4000]: 

Starting at 0x108000... 

#!ImageInfo 
# 
#    +------------------------------+ 
#    |   CISCO Cache Engine image   | 
#    +------------------------------+ 
# 
SUPPORTED_PRODUCTS=CE505,CE550 
UNCOMPRESSED_CKSUM=0x8ac40561 
UNCOMPRESSED_SIZE=0x2ae678 
COMPRESSED_CKSUM=0x33dca183 
COMPRESSED_SIZE=0x121c6b 
# 

Self decompressing the image : ###################################################
################################### [OK] 
Launching the image, please wait... 
.................. 
Console IO Initialized 
Host Name: bootHost 
User: admin 
Attaching network interface lo0... done.

Restricted Rights Legend

Use, duplication, or disclosure by the Government is 
subject to restrictions as set forth in subparagraph 
(c) of the Commercial Computer Software - Restricted 
Rights clause at FAR sec. 52.227-19 and subparagraph 
(c) (1) (ii) of the Rights in Technical Data and Computer 
Software clause at DFARS sec. 252.227-7013. 

           Cisco Systems, Inc. 
           170 West Tasman Drive 
           San Jose, California 95134-1706 

Cisco Cache Engine 
Copyright (c) 1986-2000 by Cisco Systems, Inc. 
Software Release: CE ver 2.10 (Build: FCS  04/05/00) 
Compiled: 16:53:37 Apr  5 2000 by morlee 
Image text-base 0x108000, data_base 0x3926c4 

System restarted by Reload 
The system has been up for 7 seconds. 
System booted from "flash" 

SVCINIT - phase complete 
Initializing SCSI interface... 
Initializing SCSI controller... 
Configuring SCSI peripherals... 
ID LUN VendorID    ProductID     Rev. Type  Blocks  BlkSize pScsiPhysDev 
-- --- -------- ---------------- ---- ---- -------- ------- ------------ 
 0  0  QUANTUM  VIKING II 9.1SCA 5520   0  17836668    512    0x008c0458 
 1  0  QUANTUM  VIKING II 9.1SCA 5520   0  17836668    512    0x008bf04c 

DEVINIT - phase complete 
FSINIT - phase complete 
aBypassing NVRAM Configuration... 
---------------------------------------------------------------------- 
"admin" super-user account is NOT password protected 
SECURITY ALERT: Please password protect the above super-user accounts! 
---------------------------------------------------------------------- 
CONF - phase complete 
NTP: Waiting (2 minutes) for network initialization 
SNMP: Waiting (2 minutes) for network initialization 
Mon Jul 10 05:07:19 2000: * Warning *: No ip name-servers have been configured 
  http incoming proxy, http object url-validation and dns-cache 
  require an ip name-server 
START - phase complete 

cepro#configure terminal Enter configuration commands, one per line. End with CNTL/Z 

cepro(config)#user modify username admin password cisco Operation successful 
cepro(config)#exit cepro#write Building configuration.... . [OK] 
cepro#reload Proceed with reload?[confirm] 

303949 bytes 
copying bootagent 
boot start: 0x7fee000 
starting new system - entry 0x8010 
0x43d22 
  
Press any key to stop auto-boot... 
h 
[CE500 Series]: c '.' = clear field;  '-' = go to previous field;  ^D = quit 

 boot device (flash,net) [               flash]: 
               file name [                    ]: 
        cache IP address [                    ]: 
         IP network mask [                    ]: 
       server IP address [                    ]: 
      gateway IP address [                    ]: 
 protocol (rcp,ftp,tftp) [                    ]: 
                username [                    ]: 
                password [                    ]: 
                   flags [              0x4000]: 0x0 

. . [CE500 Series]: @ boot device (flash,net) [               flash]: 
                   flags [                   0]: 

Starting at 0x108000... 

#!ImageInfo 
# 
#    +------------------------------+ 
#    |   CISCO Cache Engine image   | 
#    +------------------------------+ 
# 
SUPPORTED_PRODUCTS=CE505,CE550 
UNCOMPRESSED_CKSUM=0x8ac40561 
UNCOMPRESSED_SIZE=0x2ae678 
COMPRESSED_CKSUM=0x33dca183 
COMPRESSED_SIZE=0x121c6b 
# 

Self decompressing the image : ############################################
########################################## [OK] 
Launching the image, please wait... 
.................. 
Console IO Initialized 
Host Name: bootHost 
User: admin 
Attaching network interface lo0... done. 

              Restricted Rights Legend 

Use, duplication, or disclosure by the Government is 
subject to restrictions as set forth in subparagraph 
(c) of the Commercial Computer Software - Restricted 
Rights clause at FAR sec. 52.227-19 and subparagraph 
(c) (1) (ii) of the Rights in Technical Data and Computer 
Software clause at DFARS sec. 252.227-7013. 

           Cisco Systems, Inc. 
           170 West Tasman Drive 
           San Jose, California 95134-1706 

Cisco Cache Engine 
Copyright (c) 1986-2000 by Cisco Systems, Inc. 
Software Release: CE ver 2.10 (Build: FCS  04/05/00) 
Compiled: 16:53:37 Apr  5 2000 by morlee 
Image text-base 0x108000, data_base 0x3926c4 

System restarted by Reload 
The system has been up for 7 seconds. 
System booted from "flash" 
  

SVCINIT - phase complete 
Initializing SCSI interface... 
Initializing SCSI controller... 
Configuring SCSI peripherals... 
ID LUN VendorID    ProductID     Rev. Type  Blocks  BlkSize pScsiPhysDev 
-- --- -------- ---------------- ---- ---- -------- ------- ------------ 
 0  0  QUANTUM  VIKING II 9.1SCA 5520   0  17836668    512    0x008c0458 
 1  0  QUANTUM  VIKING II 9.1SCA 5520   0  17836668    512    0x008bf04c 

DEVINIT - phase complete 
FSINIT - phase complete 
acConfiguring from NVRAM... 
---------------------------------------------------------------------- 
All super-user accounts are password protected 
---------------------------------------------------------------------- 
CONF - phase complete 
NTP: Waiting (2 minutes) for network initialization 
SNMP: Waiting (2 minutes) for network initialization 
Mon Jul 10 05:08:53 2000: * Warning *: No ip name-servers have been configured 
  http incoming proxy, http object url-validation and dns-cache 
  require an ip name-server 
START - phase complete 

Username: admin 
Password: !--- The password is now cisco  cepro#
	
		说明：
	

	
		以上典型配置有很多已经是厂商停产产品，但是，不少设备往往还有运行，关于该设备的配置或者方案优化，你可以联系蓝盟，我们的资深工程师会给你意外的惊喜！上海蓝盟网络技术有限公司于2002年成立，业务涵盖IT外包、电脑维护、网络维护、网管外包、驻场服务、人员派驻、应急支持、系统集成、网络搬迁、网络升级、数据备份、综合布线、电脑维修、计算机维护、计算机维修，网络改造、网络整理、网络调试、局域网组建、 应急上门、数据恢复、网络咨询、服务管理、运维咨询、ITIL培训、ITSS咨询等，拥有近200名工程师，正在为近500家客户提供“一站式” 的IT外包服务。网址：www.lanmon.com www.lanmon.net 官方微博：http://weibo.com/lanmon2012 咨询电话：4008200159 蓝色学苑：www.bluestudy.net

上一篇: 蓝盟IT外包，元宇宙：四梁八柱是什么
下一篇: cisco cache egine 2050
分享到：

微软云

IT采购

弱电工程

系统集成

客户故事

cisco cache engine500

Password Recovery Procedure

for the Cisco Cache Engine 500

Description

Step-by-Step Procedure

Example of Password Recovery on a Cisco Cache Engine 500

400-635-8089